Jump to content
3DCoat Forums

How to make a Spline for the Spline menu


 Share

Recommended Posts

  • 2 weeks later...
  • 3 years later...
  • Carlosan changed the title to How to make a Spline for the Spline menu
  • Advanced Member

Those who stop by to make additional custom splines are recommended to also look at the following documentation.

It's from the wiki...
It's a good idea to make this important information easy for beginners to find.:o

Original Wiki : General curves 2021
https://3dcoat.com/dokuwiki/doku.php?id=general:curves

Original Wiki : Sculpt curves

https://3dcoat.com/dokuwiki/doku.php?id=general:sculpt_workspace:curves

Spline model specifications (★)
https://docs.google.com/document/d/1XSWUJmaLAlmz-PuQS5Q6bdGVhtgoP0-dGD40YHmgaUs/edit
 

This article explains how to specify a 'start-middle-end' part of a spline.

 

test result

1670443616_bandicam2021-07-3013-49-22-395.thumb.jpg.b08a7f1095ae400fb798240ddc3d1466.jpg

Edited by Carlosan
wiki links updated
  • Like 1
Link to comment
Share on other sites

  • Member
On 7/30/2021 at 12:48 PM, Yousung said:

Those who stop by to make additional custom splines are recommended to also look at the following documentation.

It's from the wiki...
It's a good idea to make this important information easy for beginners to find.:o

Original Wiki : General curves 2021
https://3dcoat.com/dokuwiki/doku.php?id=general:curves

Original Wiki : Sculpt curves

https://3dcoat.com/dokuwiki/doku.php?id=general:sculpt_workspace:curves

Spline model specifications (★)
https://docs.google.com/document/d/1XSWUJmaLAlmz-PuQS5Q6bdGVhtgoP0-dGD40YHmgaUs/edit
 

This article explains how to specify a 'start-middle-end' part of a spline.

 

test result

1670443616_bandicam2021-07-3013-49-22-395.thumb.jpg.b08a7f1095ae400fb798240ddc3d1466.jpg

How did you do it, I can only use one file setting at a time, and I cannot set top, middle, and bottom at the same time. Can you tell me the solution?

Link to comment
Share on other sites

  • Advanced Member
15 minutes ago, Tubor said:

How did you do it, I can only use one file setting at a time, and I cannot set top, middle, and bottom at the same time. Can you tell me the solution?


1456128650_Exportobjecttosplinespannel.thumb.jpg.a0908c685f5ef919f7ff17c55ec867db.jpg

Select the top/middle/bottom objects at once and drag and drop them to the Splines panel

or RMB menue -> Export -> Saves to Splines Pannel

 

869909846_bandicam2021-07-3117-07-23-569.thumb.jpg.9a7c8f31db6a71bc91cedcafc903a38e.jpg

At this time, it seems that it is not recognized properly, but if you press OK after adjusting the space, the middle part is recognized properly.

 

  • Like 1
Link to comment
Share on other sites

  • Advanced Member
2 hours ago, Tubor said:

If I want to use models that cannot be overlapped, how can I create an effect similar to the built-in software?

I'm not sure what exactly you mean by 'cannot be overlapped.'

If you want to connect the rope like the picture very precisely
It would be good to use the poly model added in this 2021 version.

I'm still learning, so I'm going to test this over the weekend :)

Link to comment
Share on other sites

  • Member
1 hour ago, Yousung said:

I'm not sure what exactly you mean by 'cannot be overlapped.'

If you want to connect the rope like the picture very precisely
It would be good to use the poly model added in this 2021 version.

I'm still learning, so I'm going to test this over the weekend :)

Thank youYousung

,I am also a beginner and hope to make progress together

Link to comment
Share on other sites

  • 3 weeks later...
14 hours ago, Yousung said:

Check.jpg.019db08c84bdb29d66bb2b70da708592.jpg

If the middle part of the model does not repeat, check the following

1. Is the object named as follows?
- Top_@@@
- Middle_@@@
- Bottom_@@@

2. Is the connection part of the object 'Open edge'?
- Spline guidelines say that the top-middle-bottom part should be an open edge

3. This is just in case, but have you actually registered and tested it instead of a preview in the creation stage?
- It does not seem to be repeated in the preview, but if you follow steps 1 and 2 properly, the result will be repeated middle-parts normally.

 

  • Thanks 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...