Advanced Member tokikake Posted April 29, 2019 Advanced Member Report Share Posted April 29, 2019 I have not seen this problem before (or could adjust some property then do again, it have wroked,,) But about sculpt mesh (made by rotate surface), I can not manually retopo with Stroke and path. it only generate 2 side(first and end) poligons around sculpt mesh. I change stroke ,path more short (just start from bottome to middle height of mesh) but it show same. (only 2 line poligons are generated) Can someone test this scene please? https://www.dropbox.com/s/fl1c0ucuthywvht/vasetest.3b?dl=0 At first I tried to keep Suface mode (sculpt mesh), and change as Voxel mode (with dense), after all not work. change Spline points density high and low, neither not work . So I think I miss use some option,, my 3d coat version is 4.8.38.SL (windows 64bit Open GL) Quote Link to comment Share on other sites More sharing options...
Carlosan Posted April 30, 2019 Report Share Posted April 30, 2019 Something this happen if the model is very tiny. Try scaling it a bit. Quote Link to comment Share on other sites More sharing options...
Advanced Member tokikake Posted April 30, 2019 Author Advanced Member Report Share Posted April 30, 2019 2 hours ago, Carlosan said: Something this happen if the model is very tiny. Try scaling it a bit. Thanks advice, but when I use measure tool, it is almost 240 mm (24cm etc), and recently i just use default settings about scale things. Then do not know how 3d coat count mesh too tiny etc.. then as you suggested, I scale up 2.5 and increease resolution with surface mode. and try more simple short path, but not generate well. I know sometimes, if the path end or start are located bottom faces, (hard angle), the area cause issue, but usually middle stroke area generate well, but about this mesh (use new curve tool) I can not generate faces well,,It try with surface mode, dense mesh, (wire frame to check) Only bottom area , generate poligons. Quote Link to comment Share on other sites More sharing options...
Carlosan Posted May 1, 2019 Report Share Posted May 1, 2019 Can you share the file to look around ? Quote Link to comment Share on other sites More sharing options...
Advanced Member tokikake Posted May 1, 2019 Author Advanced Member Report Share Posted May 1, 2019 (edited) 7 hours ago, Carlosan said: Can you share the file to look around ? Of course. I hope you test it please. Here is drop box link of the file. vase-surface.3b Edited May 1, 2019 by tokikake Quote Link to comment Share on other sites More sharing options...
Carlosan Posted May 1, 2019 Report Share Posted May 1, 2019 You are right, cant get it working. I am reporting this as bug. Thx for point it up. Quote Link to comment Share on other sites More sharing options...
Contributor Tony Nemo Posted May 2, 2019 Contributor Report Share Posted May 2, 2019 I have had many stroke failures over time. Some leave random faces inside the model that must be ghosted to find and delete. Quote Link to comment Share on other sites More sharing options...
Advanced Member tokikake Posted May 2, 2019 Author Advanced Member Report Share Posted May 2, 2019 Thanks to take your time Carlosan. Then as you know, I made this mesh, to test new Swept Curve option (Rotate Surface), htne it seems not work for me. but when I made almost same shape (voxel), by Primitive tool (adjust curve graph) , then Strokes tool not cause issue. I think if mesh made by swept tool (surface mode) can keep edge shape good, but cause kind of problem when re-topo with strokes tool ,, Though there may be workflow, voxelize and clean it. (I could not do it well) Quote Link to comment Share on other sites More sharing options...
Advanced Member tokikake Posted May 2, 2019 Author Advanced Member Report Share Posted May 2, 2019 16 minutes ago, Tony Nemo said: I have had many stroke failures over time. Some leave random faces inside the model that must be ghosted to find and delete. Yes I understand what Tony mentioned. but I could not clean it well about the mesh (surface) generated by the swept rotate surface tool. I tried it change as voxel . then scale,, and fill or close hall ,smooth etc , but there seems issue here or there in volume. (voxel arrange is somehow different from usuall clean voxel mesh),, then after all,, test with Surface mode. As for me, I can not find issue about the mesh. but apreciate if you test the file. (up-loaded link) Quote Link to comment Share on other sites More sharing options...
Carlosan Posted May 2, 2019 Report Share Posted May 2, 2019 Test done: same error. Quote Link to comment Share on other sites More sharing options...
Advanced Member tokikake Posted May 2, 2019 Author Advanced Member Report Share Posted May 2, 2019 1 hour ago, Carlosan said: Test done: same error. Yes thanks! then I think, my mesh seems too thin when I generate with swept rotation. as Tony adviced,,, (so it cause double side mesh ) if I set plenty thickness when generate , and remove curve,, and voxelize, seems work.. ( keep thin voxel mesh for bake only, copy another mesh which add more thickness and voxelize,, may work I feel,, I may try again,, this workflow. Quote Link to comment Share on other sites More sharing options...
Gorbatovsky Posted November 11, 2019 Report Share Posted November 11, 2019 On 4/30/2019 at 2:45 AM, tokikake said: I have not seen this problem before (or could adjust some property then do again, it have wroked,,) But about sculpt mesh (made by rotate surface), I can not manually retopo with Stroke and path. it only generate 2 side(first and end) poligons around sculpt mesh. I change stroke ,path more short (just start from bottome to middle height of mesh) but it show same. (only 2 line poligons are generated) Can someone test this scene please? https://www.dropbox.com/s/fl1c0ucuthywvht/vasetest.3b?dl=0 At first I tried to keep Suface mode (sculpt mesh), and change as Voxel mode (with dense), after all not work. change Spline points density high and low, neither not work . So I think I miss use some option,, my 3d coat version is 4.8.38.SL (windows 64bit Open GL) Hi. Thanks for the feedback. In the development of a new version of the tool Stroke. 1 Quote Link to comment Share on other sites More sharing options...
Carlosan Posted November 11, 2019 Report Share Posted November 11, 2019 Solved on version 4.9.33 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.